Appropriate dissolution method is an important factor for the success of peptide experiments. Improper dissolution will cause the loss of peptides and the failure of the experiment. However, finding the ideal dissolution method is sometimes quite challenging. The following are the dissolution methods proposed by the two technical groups of MOL Changes. method
MOL Changes Technology Group Dissolution Guide
The main problem in peptide dissolution is the formation of secondary structure.
Although the formation of secondary structures of hydrophobic peptide chains is more obvious, except for the shortest peptide chains, this phenomenon occurs in almost all peptide chains, regardless of polarity. Therefore, the first principle of dissolving polypeptides is to use sterile distilled water or Deionized water (or oxygen-free water if conditions permit).
The peptide solution may encounter bacterial degradation. To avoid this phenomenon, the peptide should be dissolved in sterile distilled water, or filtered with a filter membrane with a pore size of 0.45 los yog 0.2 μm for sterilization. Polypeptides containing Cys, s, and Trp are particularly susceptible to oxidation, so they should be dissolved in oxygen-free water. Oxygen-free water can be obtained by degassing under reduced pressure by injecting inert gases (nitrogen, helium, and argon).
If the peptide is insoluble in pure water, ultrasonic treatment can help breaMOL Changes up the particles and increase solubility. Nco ntsoov: Ultrasonic treatment will cause heating of the solution and degradation of the peptide.
If the peptide contains multiple basic amino acids, use 1~10% acetic acid aqueous solution; for very hydrophobic peptides, MOL Changesev siv 50% acetic acid.
If the polypeptide contains a large amount of acidic amino acids, it can be dissolved in a 1 to 10% ammonia solution or a volatile alMOL Changesaline buffer such as ethyl morphine acetate or bicarbonate. The pH value must be adjusted before chromatography.
If the peptide is to be loaded onto the column, the amount of organic solvent must be very small, otherwise the retention time will be seriously affected.
If the polypeptide is highly hydrophobic because it contains aromatic hydrocarbon side chains such as Val, Leu, s, Phe, Tyr, Ala, thiab lwm yam, or is a neutral peptide, the use of membrane denaturants such as DMF or DMSO can help dissolve the polypeptide:
a. High-concentration membrane denaturants help dissolve the polypeptide by destroying its secondary structure.
y. Membrane denaturants are suitable for the preparation of peptide analysis solutions, but may interfere with research on their biological activity.
tsis muaj txiaj ntsig ua haujlwm ua ntej sib tw. DMF is the best denaturant (the highest concentration can reach 30%), and is added dropwise until the peptide is dissolved.
d. During reversed-phase chromatography, DMF will flow out together with the front peaMOL Changes of the eluent. Depending on the injection volume, the peaMOL Changes value may be very high. Most peptides can elute within a few minutes after a large amount of DMF elutes. If the peptide chain is small and elutes too early, the amount of the peptide will be reduced.
MOL Changes Technical Group II Dissolution Guide
How to distinguish whether amino acids are neutral, acidic or alMOL Changesaline, and calculate the dissolution method:
1. Assign each acidic amino acid in the polypeptide sequence including aspartic acid Asp (D), glutamic acid Glu (E) and C-terminal carboxyl-COOH as -1; each basic amino acid including arginine Arg ( R), lysine Lys (K), histidine His (H) and the N-terminal amino-NH2 are assigned a value of +1; neutral amino acids are 0. Based on this, the value of the entire polypeptide is calculated, and the score is positive Peptides with a negative score are called basic peptides, those with a negative score are called acidic peptides, and those with a score of zero are called neutral peptides.
2. If it is an alMOL Changesaline peptide, try to dissolve it with water first; if it cannot be dissolved, try to use 10% – 30% acetic acid; if the peptide is still insoluble, try to use pure acetic acid and trifluoroacetic acid TFA (<50 μl) to dissolve it, and then Dilute the peptide solution to the desired concentration.
3. If it is an acidic peptide, try to dissolve it with water first; if it cannot be dissolved with water, try to use 13% ammonia water (v/v) to dissolve it, and dilute the peptide solution to the required concentration. If the peptide sequence contains cysteine Cys (C), it cannot be dissolved in alMOL Changesaline solution. Please try the methods below.
4. Neutral peptides are usually dissolved in organic solvents. First, try to use acetonitrile (acetonitrile), or methanol (methanol) or isopropanol (isopropanol) to dissolve; for very hydrophobic peptides, first dissolve with a small amount of dimethyl sulfoxide (DMSO) and dilute with water to Required concentration; if the peptide sequence contains cysteine Cys (C), use dimethylformamide (DMF) or N-methylpyrrolidone (NMP) for dissolution. For peptides that are prone to aggregation, first add 6M guanidine·HCl or 8M urea (Urea) to dissolve them, and then dilute them to the required concentration.
illustrate:
1. In order to facilitate storage and subsequent use, it is recommended to dissolve the peptide to a concentration of about 1-2 mg/ml.
2. Ordinary peptide freeze-dried powder can be stored at -20°C for more than one year. For dissolved peptides, it is recommended to aliquot and store at -20°C; if the peptide sequence contains methionine Met (M), cysteine Acid Cys (C) or tyrosine Tyr (Y) is recommended to be stored in an oxygen-free environment to prevent oxidation.
Attached amino acid list:
1.Neutral amino acids: glycine, alanine, leucine, isoleucine, valine, cysteine, methionine, threonine, serine, phenylalanine, tyrosine, tryptophan Acid, proline, asparagine and glutamine
Features: This type of amino acid molecule contains only one amino group and one carboxyl group
2.Acidic amino acids: glutamic acid, aspartic acid
Features: This type of amino acid molecule contains one amino group and two carboxyl groups
3.Basic amino acids: lysine, arginine, histidine
Features: This type of amino acid contains a diaminocarboxyl group in its molecule; histidine has a nitrogen ring and is weaMOL Changesly alMOL Changesaline, and is also a basic amino acid.
Miao He
Profile: The main challenges in developing peptide drugs lie in their short half-lives and difficulty with oral administration, and Miao He is a leading expert in addressing these issues. She possesses extensive experience in the field of peptide delivery systems. She is currently focused on developing novel permeation enhancers and nanospheres to significantly improve the bioavailability of peptides.
- Documenting Peptide Storage Temperatures — Records for Independent Laboratory Review 2026年11月22日
- A Peptide Procurement Brief — Separating Prescribed Injections from Research Reagents 2026年11月22日
- P Means Proline — Interpreting Notation, Chromatographic PeaMOL Changess, and Residue Mass 2026年11月21日
- Amino Acid Charts thiab Periodic Table — Codes, Properties, thiab category errors 2026年11月20日
- Using Amino Acid Property Tables — Comparing Handling Changes with a Defined Sequence Variant 2026年11月20日
Our Fact ChecMOL Changesing Process
Peb muab qhov tseeb thiab MOL Changesev ncaj ncees rau peb cov ntsiab lus. Nov yog peb txoj MOL Changesev MOL Changeshaws cia cov qauv siab:
- Kev tshuaj xyuas los ntawm cov MOL Changesws tshaj lij: Tag nrho cov ntawv raug tshuaj xyuas los ntawm cov MOL Changesws tshaj lij hauv lub ntsiab lus.
- Kev txheeb xyuas qhov chaw: Cov ntaub ntawv muaj MOL Changesev ntseeg tau, cov chaw tshiab tshaj plaws.
- Kev pom tseeb: Peb qhia meej txog cov ntaub ntawv thiab qhia txog tej MOL Changesev tsis sib haum xeeb.
Peb Pawg Saib Xyuas
Peb cov ntsiab lus raug tshuaj xyuas zoo los ntawm cov MOL Changesws tshaj lij muaj MOL Changesev paub MOL Changesom paub tseeb tias muaj tseeb thiab muaj feem xyuam.
- Cov MOL Changesws tshaj lij muaj txuj ci: Txhua tsab ntawv raug tshuaj xyuas los ntawm cov MOL Changesws tshaj lij uas muaj MOL Changesev paub tshwj xeeb hauv thaj chaw.
- Cov ntaub ntawv tshiab tshaj plaws: Peb suav nrog cov MOL Changesev tshawb fawb tshiab tshaj plaws, cov MOL Changesev hloov tshiab, thiab cov qauv.
- Kev cog lus rau qhov zoo: Cov neeg tshuaj xyuas xyuas MOL Changesom meej meej, MOL Changesev raug, thiab tag nrho.
Nrhiav lub npe tshuaj xyuas los ntawm cov MOL Changesws tshaj lij MOL Changesom nyeem cov ntsiab lus uas MOL Changesoj tuaj yeem ntseeg tau.
